Soundcore Earbuds Pairing: How to Connect, Reset, and Fix Problems

TL;DR
Open the charging case, and many Soundcore earbuds enter pairing mode on their own. Then pick them from your Bluetooth list. If that doesn’t work, leave the lid open and hold the case button for 3 seconds. If they still won’t connect, forget them on your phone and reset them by holding the case button for about 10 seconds.

Your new Soundcore earbuds are charged, but your phone can’t find them. Soundcore earbuds pairing means linking the buds to a phone, tablet, or computer over Bluetooth. On many models, opening the case starts pairing mode automatically. Then you choose the earbuds from your Bluetooth list. If that fails, hold the case button for 3 seconds, or reset them. Below are the exact steps and fixes.

Soundcore earbuds pairing mode with white lights flashing inside the open charging case

How Do You Pair Soundcore Earbuds for the First Time?

Soundcore makes many models, and the steps vary a little. The basic idea stays the same. These steps match Soundcore’s guides for models like the Space A40 and Liberty 4 NC.

1. Charge the earbuds and case. A low battery can stop pairing.
2. Turn on Bluetooth on your phone, tablet, or computer.
3. Open the charging case lid. On the Space A40, the earbuds power on and enter pairing mode by themselves.
4. Watch the lights. White lights flash when the earbuds are ready to pair.
5. Open your Bluetooth list. Select the earbuds by name, such as “Soundcore Space A40.”
6. Confirm any pop-up. Tap Pair when asked.
7. Install the Soundcore app on your phone for EQ, controls, and updates.

If you accidentally tap Cancel on the pairing pop-up, turn Bluetooth off and on, then try again. Soundcore’s Liberty 4 NC page gives this tip.

What do the pairing lights mean?

Lights tell you what’s happening, but colors and patterns differ by model:

• The Space A40: LEDs flash white in sequence when pairing mode is active.
• The Liberty 4 NC: The left and right white lights in the case flash quickly in pairing mode.
• After connecting: The lights usually stop flashing or turn steady for a moment.

If your lights look different, check your model’s manual.

What about Android’s Google Fast Pair?

Some Soundcore models support Google Fast Pair on Android. An optional pop-up appears when you open the case near your phone when Fast Pair is enabled. Tap it to connect. Soundcore’s own blog lists the Liberty 4 NC as supporting it. The same blog says the Space A40 doesn’t, so you’d use the regular Bluetooth menu instead.

How Do You Put Soundcore Earbuds in Pairing Mode Manually?

Sometimes the earbuds are already paired with another device. In that case, they won’t enter pairing mode on their own. Use one of these methods:

Situation	What to do
Earbuds are in the case, and you want pairing mode	Leave the lid open, then hold the case button for 3 seconds until the white LEDs flash
Earbuds are connected to another device, and you want to add a new one	Wear the earbuds, then press and hold the touchpad on both earbuds for 3 seconds at the same time
Older or simpler models, like the Life Dot 2 or Liberty Neo	Take both earbuds out and hold their touch or multifunction buttons for about 3 seconds

The first two methods come from Soundcore’s Space A40 guide. The Liberty 4 NC page also lists holding both earbuds for 3 seconds. The third row comes from older model guides. Always check your own model’s guide, since hold times can vary.

How Do You Connect Soundcore Earbuds to Different Devices?

Put the earbuds in pairing mode first. Then follow the steps for your device.

iPhone or iPad

1. Open Settings, then tap Bluetooth.
2. Wait for your earbuds to appear under Other Devices.
3. Tap the name to connect.

Android phone or tablet

1. Open Settings, then Connected devices (the name varies by brand).
2. Tap Pair new device.
3. Choose your earbuds from the list.

Windows computer

1. Open Settings, then Bluetooth & devices.
2. Select Add device, then Bluetooth.
3. Pick your earbuds from the list.

Mac

1. Open System Settings, then Bluetooth.
2. Find your earbuds in the list.
3. Click Connect.

Keep this in mind: Soundcore’s Liberty 4 NC page says its app doesn’t currently work on computers. So pair the earbuds with your phone first to use the app. Then pair them with your computer.

Can You Connect Two Devices at Once?

On some models, yes. This feature is called multipoint. For example, you could stay connected to your phone and laptop at the same time.

On the Space A40, follow these steps:

1. Connect the earbuds to your first device.
2. Open the Soundcore app.
3. Go to Settings, then Dual Connections.
4. Choose Connect New Device, then pair the second device.

Support depends on the model. Soundcore’s blog also notes that turning on LDAC on the Space A40 switches multipoint off. Check your model’s specs before you rely on it.

Does Your Bluetooth Version Matter for Pairing?

Mostly not. The Bluetooth technology works across phone versions, so a new pair of earbuds will still work with an older device. Newer versions usually improve range, stability, and battery use. For example, Soundcore lists Bluetooth 5.3 for the Liberty 4 NC.

You don’t need matching versions. If pairing fails, the cause is more often a bad saved pairing, a low battery, or interference than the version number.

How Do You Reset Soundcore Earbuds?

A reset clears the saved pairings and fixes many stubborn problems. It also helps if the left and right earbuds stop talking to each other. Try this for models like the Space A40 and Liberty 4 NC:

1. Forget the earbuds in your phone’s Bluetooth list.
2. Put both earbuds in the charging case. Leave the lid open.
3. Hold the case button for about 10 seconds.
4. Watch the LEDs. They flash three times when the reset works.
5. Wait for pairing mode. The earbuds then restart, ready to pair.
6. Pair them again from your Bluetooth list.

Soundcore lists the same 10-second method for the Space A40, Liberty 4 NC, and P40i. Some models use a different method. For example, one older guide says to tap and hold the logo area on both earbuds for 10 seconds. Check your own model if the case-button method doesn’t work.

Why Won’t Your Soundcore Earbuds Pair?

Work through these checks in order:

1. Charge everything. Low power can block pairing.
2. Confirm pairing mode. The lights should flash.
3. Turn Bluetooth off and on on your phone.
4. Forget the earbuds and pair again. On an iPhone, open Settings, Bluetooth, tap the i next to the earbuds, then choose Forget This Device. Wait about 30 seconds before trying again.
5. Turn off Bluetooth on nearby devices. Your earbuds might be auto-connecting to a laptop or old phone.
6. Move closer and away from busy Wi-Fi routers or other wireless gear.
7. Update your phone and the Soundcore app.
8. Clean the case contacts. Remove dust with a dry cloth, then reseat the earbuds.
9. Reset the earbuds using the steps above.
10. On Windows, remove the earbuds in Bluetooth settings, then add them again.
11. Contact Soundcore support if nothing works. A warranty replacement may be possible.

What if only one earbud works?

Put both earbuds back in the case and reset them. Soundcore’s Space A40 guide says a reset can fix problems where the earbuds don’t pair with each other. After the reset, pair them again from scratch.

What should you do before pairing to avoid problems?

• Keep only one device in pairing mode at a time.
• Delete old pairings you don’t use.
• Pair at home, where the Bluetooth list is short and easy to read.
• Start with low volume. Then raise it after you connect.

Which Soundcore Earbuds Are Easiest to Pair?

Most Soundcore models use the same basic idea: open the case, and select the earbuds. A few differences can make pairing smoother:

• Liberty 4 NC: Supports Google Fast Pair on Android, so a pop-up appears when you open the case.
• Space A40: Pairs through the normal Bluetooth menu. It adds Dual Connections in the app.
• Liberty 5: Soundcore lists a case-button reset that flashes three LEDs.

Pick based on features, not pairing difficulty. All three are easy once you know the steps. Prices change often, so check the live price before you buy.

Conclusion

Soundcore earbuds pair easily once you know the pattern. Open the case, pick the earbuds in your Bluetooth list, and hold the case button for 3 seconds if they don’t appear. If the issue continues, forget the earbuds and reset them by holding the case button for 10 seconds.

Grab your earbuds and try the steps now. Then explore more earbud guides at Techprixo, and share this article with a friend who’s stuck on a flashing light.

Disclaimer

This article may contain affiliate links. If you purchase through these links, Techprixo may earn a small commission at no extra cost to you.

FAQ